Intellinet-network-solutions 523615 Uživatelský manuál

INT-523608/523615-UM-0307-02

10• The IP address is between 192.168.10.2 and 192.168.10.254• The subnet mask is 255.255.255.0• The default gateway is 192.168.10.1

113.2 Windows XP Setup1. Install the High-Speed Broadband Router.2. Start Windows XP and check whether the LAN LED is on or off. If o

12

13

148. Click “Start” ➝ “Run”; enter “cmd“; click “OK.”9. Type “ipconfig” in the pop-up command window.NOTE: Make sure the IP informatio

1511. Input “ping 192.168.10.1,” then “Enter.”12. If you can see “Reply from 192.168.10.1: bytes=32 time=2ms TTL=64,” then theconnect

16Click the “Login” button to enter the configuration and configure the router manually.This may be required if the Internet Wizard f

173. Select the “PPPoE User (ADSL)” radio button.4. Key in the “User ID” and “Password” provided by your Internet service provider.5.

18If “Conn. Status” is unchanged, check whether your service type is correct.7. Confirm the WAN connection status: If the WAN connect

19“Connect” is a manual connection button. By clicking it, the system can beconnected to the Internet again.Click “Save” to save the

2TABLE OF CONTENTSSection 1: Introduction... 3

20On Demand is only effective for Disconnect PPP session if idle time is longerthan _ Min.Connect Manually: With this option, users h

216. If Conn. State remains as “Connecting to Internet,” do the following:• Close the pop-up window.• Turn the cable modem power off

22The “Connect” button is a manual WAN port IP address refresh function button. Ifclicked, the WAN port will re-obtain a dynamic IP a

233. Input WAN IP Address, Subnet Mask, Default Gateway, Primary DNS Server andSecondary DNS Server as provided by your ISP.4. Click

24If the WAN connection is successfully established, you can see the following:• Connection Type should be “Static IP”• Connection St

25This page shows current Internet connection status (WAN port), includingConnection Type, Connection Status, WAN IP Address, Subnet

26LAN Information: Shows the router’s current LAN connecting status, DHCP serversettings, including MAC address (physical address) of

27PPPoE (ADSL), Dynamic IP and Static IP setup procedures are illustrated in sections4.2, 4.3 and 4.4, respectively.4.6.2 LAN SetupCl

28DHCP Server Status: The current status of the DHCP server.DHCP Server Operation: Enable or disable the DHCP server.DHCP IP Pool: Th

29Internet Access Restriction: You can define the maximum number of clients withaccess to the Internet at the same time. The default

3 4.9.5 NAT On/Off...49 4.10 Advanced

30Picture showing 4 Port VersionLink information, port speed and port statistics are shown on this page.Link Setup: This section is f

31Mode: Automatic mode and manual mode on/off. In Manual mode, you can definethe connection speed. Auto is the default and recommende

32 NOTE: Save the router configuration after completion; otherwise, theconfiguration will be lost after the router is restarted. 4.6.

33Login Account Setup: Enter your old ID and password and the new values. Click“Apply” to save the changes. The default Login ID is “

344.7.2 Firmware UpgradeClick “System” ➝ “Firmware Upgrade.”Firmware updates may be available from time to time for the router. Befor

354. Click on “Browse” and select the new firmware file. Click “Open.”5. Click “Upgrade” to start the upgrade process.

36The Router will restart automatically after the upgrade process is completed. Afterthe upgrade, verify the firmware version. NOTE:

374.7.4 Access ListClick “System” ➝ “Access List.”Access ListWith this function you can limit access to the router based on the IP ad

38Hostname Setup: Configure the router’s device name used in the network.Config Mgmt/Restart:Config Backup: Back up the configuration

39UPNP Setup: UPnP allows devices to connect seamlessly and to simplify theimplementation of networks in the home (data sharing, comm

4DHCP Server Supported: All of the networked computers can retrieve TCP/IPsettings automatically from this device.Static IP Address B

40QoS Basic Setup: QoS stands for “Quality of Service.” It allows the control ofInternet bandwidth based on different criteria such a

414.8.3 Application QoSClick “QoS” ➝ “Application QoS.”Define the maximum bandwidth available, or the minimum guaranteed bandwidthfor

424.8.4 Ports QoSClick “QoS” ➝ “Port QoS.”Define the maximum bandwidth available, or the minimum guaranteed bandwidthfor TCP or UDP p

434.9 NAT4.9.1 ApplicationsClick “NAT” ➝ ”Applications.”Some programs, such as Internet network games, filesharing programs and Inter

44lease IP for the client PC is recommended (Basic Setup ➝ LAN/DHCP).The following list shows all applications and the ports they use

454.9.2 Internal ServerClick “NAT” ➝ “Internal Server.”The NAT firewall protects the computers in the local network from unauthorized

46Setup Method:1. Select the LAN service from the list below:ProtocolServerDNSDNS (Domain Name Server)SMTPSMTP(Simple Message Transfe

474.9.3 Port ForwardingClick “NAT” ➝ ”Port Forwarding.”Port Forwarding functions the same way as Internal Server, but it allows enter

48Internal Port Range: 17997–18003Click “Add.” Repeat the same steps, but this time with UDP (as Silent Hunterrequires both TCP and

49Protocol: Select the trigger port’s protocol (TCP/UDP).Port Range: Trigger port’s range.Port Forward: Set up the forward port.Proto

5straight-through or cross cable can be used to connect the LAN card or switch.3. Turn on the power by pressing the power button on t

504.10 Advanced Setup4.10.1 FirewallClick “Advanced” ➝ ”Firewall.”The router’s firewall consists of two main functions.1. Blocking Do

51a hacking attempt starts, because the attacker first needs to know if a target isavailable or not. With this option activated, the

52Dynamic DNS (DDNS) is a system that allows the domain name data held in a name server to beupdated in real time. The most common us

53Setup Method:1. Enter the computer’s name and the LAN card’s MAC address. Then click “Add” toadd new rule. You can search for the M

54Setup Method:Status: Current status of the URL filter: “Started” or “Stopped.”Operation: Click “Start” or “Stop” to activate or dea

55you are going to need the functionality. Remote Management should never beenabled if the default administrator password has not bee

564.10.7 VPN SetupClick “Advanced” ➝ ”VPN Setup.”The device allows five users to establish a VPN tunnel (PPTP) to the router. A VPNtu

575. SPECIFICATIONSStandards• IEEE 802.3 (10Base-T Ethernet)• IEEE 802.3u (100Base-TX Fast Ethernet)General• LAN ports: - Model 5

58• Certifications: FCC Class B, CE Mark, RoHSLEDs• Power• OP (operational status)• Power Line Link/Act• WAN Link/Act• LAN 1-4/8 Link

59

62.3.2 Model 523615, 8-PortLED IndicationPWR Continuously lit indicates power to the router.RUN/CPU Slowly blinking indicates the sys

60www.intellinet-network.comAre you completely satisfied with this product?Please contact your INTELLINET NETWORK SOLUTIONS™ dealerwi

7directly to Section 4. If you are unable to open the router’s Web Admin screen,follow whichever instructions below apply to the oper

85. Click “Local Area Connection” ➝ “Properties” ➝ “Internet Protocol (TCP/IP)” and“Properties.”

96. Click the “General” tab; select “Obtain an IP address automatically” and “Obtain DNS serveraddress automatically.”7. Click “OK.”8