Intellinet-network-solutions Wireless G Broadband Router 523431 Uživatelský manuál

INT-523431-UM-1106-01

104. Double-click “Network and Dial-up Connection” in “Control Panel.”5. Click “Local Area Connection” —> “Properties” —> “Inte

116. Click the “General” tab; select “Obtain an IP address automatically” and “Obtain DNSserver address automatically.”7. Click “OK.”

128. Click ”Start” —> “Run.”9. Input ”cmd”; then click “OK.”10. Input “ipconfig” in the pop-up command window.NOTE: Make sure your

1310. Type “ping 192.168.0.1,” then hit “Enter.”11. If you can see “Reply from 192.168.0.1: bytes=32 time=2ms TTL=64,” then the conne

143.2 Windows XP Setup1. Install the Wireless G Broadband Router.2. Start Windows XP and check whether the LAN LED is on or off. If o

15

16

178. Click “Start” —> “Run”; enter “cmd“; click “OK.”9. Type “ipconfig” in the pop-up command window.NOTE: Make sure the IP inform

1811. Input “ping 192.168.0.1,” then “Enter.”12. If you can see “Reply from 192.168.0.1: bytes=32 time=2ms TTL=64,” then the connecti

193. You will then see the following login Web page. Click the “Login” button to enterthe configuration and configure the router manu

2TABLE OF CONTENTSSection 1: Introduction... 3

203. Select the “PPPoE User (ADSL)” radio button.4. Key in the “User ID” and “Password” provided by your Internet service provider.5.

21If “Conn. Status” is unchanged, check whether your service type is correct.7. Confirm the WAN connection status: If the WAN connect

22“Connect” is a manual connection button. By clicking it, the system can beconnected to the Internet again.Click “Save” to save the

23internal function and does not affect the Connect On Demand function. ConnectOn Demand is only effective for Disconnect PPP session

246. If Conn. State remains as “Connecting to Internet,” do the following:• Close the pop-up window.• Turn the cable modem power off

25The “Disconnect” button causes the router to release the WAN port IP address anddisconnect from the Internet.The “Connect” button i

263. Input WAN IP Address, Subnet Mask, Default Gateway, Primary DNS Server andSecondary DNS Server as provided by your ISP.4. Click

27If the WAN connection is successfully established, you can see the following:• Connection Type should be “Static IP”• Connection St

28This page shows current Internet connection status (WAN port), includingConnection Type, Connection Status, WAN IP Address, Subnet

29This shows the current wireless configuration, including:Wireless Status: Current wireless connector status.Wireless MAC Address: P

3 4.10.3 WOL (Wake-on LAN)...56 4.10.4 URL Filter ...

30LAN Information: Shows the router’s current LAN connecting status, DHCP serversettings, including MAC address (physical address) of

31PPPoE (ADSL), Dynamic IP and Static IP setup procedures are illustrated insections 4.2, 4.3 and 4.4, respectively.The Wireless G Br

32Region: Configure the region depending on your location.Channel: Select the channel manually, or use the “Search for best channel”f

33This page lets you configure the LAN IP settings of the router, along with the DHCPserver settings.System IP Setup:System IP addres

34Add hardware address & IP pair on the real network: This function lets you findall computers currently connected and allows you

35Link information, port speed and port statistics are shown on this page.Link Setup:Port: The router’s WAN and LAN ports.Mode: Autom

36the connection speed. Auto is the default and recommended mode.Speed: When in Manual mode, you can define the port speed here: eith

37 Note: Save the router configuration after completion; otherwise, theconfiguration will be lost after the router is restarted.4.7 S

38 NOTE: It is strongly recommend that you change the administratorusername and password during the initial setup. Failing to do so w

394. Click on “Browse” and select the new firmware file. Click “Open.”5. Click “Upgrade” to start the upgrade process.

4DHCP Server Supported: All of the networked computers can retrieve TCP/IPsettings automatically from this device.Static IP Address B

40The Router will restart automatically after the upgrade process is completed. Afterthe upgrade, verify the firmware version. NOTE:

41(the E-Mail Setup in the Admin Configuration must be completed for this to work)and view the real-time system log of the router.4.7

42UPNP Setup: UPnP allows devices to connect seamlessly and to simplify theimplementation of networks in the home (data sharing, comm

434.8 QoS4.8.1 Basic SetupClick “QoS” —> “Basic Setup.”QoS Basic Setup: QoS stands for “Quality of Service.” It allows the control

44Setup by IP Address: You can limit or guarantee bandwidth for a single IP addressor an IP address range.IP Address: IP address or r

45Define the maximum bandwidth available, or the minimum guaranteed bandwidthfor pre-defined applications.Setup Method: Choose the ap

46Define the maximum bandwidth available, or the minimum guaranteed bandwidthfor TCP or UDP ports and port ranges.Setup Method: Enter

47Some programs, such as Internet network games, filesharing programs and Internetphones, need more than one connection. Because of t

48ApplicationPortBuddyBuddyTCP 812, TCP 987WinAmp BroadcastingTCP 8000GuruGuruTCP 9292TCP 9999NetMeetingTCP 1720WinMXTCP 6699UDP 6257

494.9.2 Internal ServerClick “NAT” —> “Internal Server.”The NAT firewall protects the computers in the local network from unauthor

5DataModulationCCK, DQPSK, DBPSK, OFDMRF Power16 – 18 dBmAntennaType1*2.4 Ghz Dipole Antenna1*2.4 Ghz Embedded AntennaCableUTP 100Bas

50Setup Method:1. Select the LAN service from the list below:ProtocolServerDNSDNS (Domain Name Server)SMTPSMTP(Simple Message Transfe

514.9.3 Port ForwardingClick “NAT” —> ”Port Forwarding.”Port Forwarding functions the same way as Internal Server, but it allows e

52External Port Range: 17997–18003Internal PC IP Address: 192.168.0.150Internal Port Range: 17997–18003Click “Add.” Repeat the same

53Rule Name: The description of adding the trigger port.Port Trigger: Set up the trigger port.Protocol: Select the trigger port’s pro

544.10 Advanced Setup4.10.1 FirewallClick “Advanced” —> ”Firewall.”The router’s firewall consists of two main functions.1. Blockin

55Blocking ICMP (ping) from Internet: A successful ping command is typically howa hacking attempt starts, because the attacker first

56Dynamic DNS (DDNS) is a system that allows the domain name data held in aname server to be updated in real time. The most common us

57called the Magic Packet. The router sends such a Magic Packet to a specificcomputer.Setup Method:1. Enter the computer’s name and t

58application from the drop-down list (e.g., eMule) to prevent local users from usingthose programs.Setup Method:Status: Current stat

59Example: http://123.456.789:8081 (remote management port set to 8081).NOTE: Remote Management should be kept turned off, unless you

6Insidefunctions10/100 Mbps switchLAN/WAN port auto sense cross cableWAN port static/dynamic IP flexible setting upSupport 64/128 bit

60The device allows five users to establish a VPN tunnel (PPTP) to the router. A VPNtunnel is a secure and encrypted connection betwe

61Appendix A: UTP Cable SpecificationsTwisted pair Category-5 straight-through cableTwisted pair Category-5 Cross over cable S

62

63

64www.intellinet-network.comAre you completely satisfied with this product?Please contact your INTELLINET NETWORK SOLUTIONS™ dealerwi

7CPUKENDIN KS8695PX (ARM9)FLASH2MB FlashMemory16 MB SDRAMLAN connectionStatic or dynamic IP addressWAN connectionXDSL Cable Modem Spe

8LEDDescriptionExplanationPWRPower LEDLong lightCPUSystem status LEDLED flashes (on-off-on-off) during normaloperation. Any other sta

9WANConnect xDSL/cable modem or LAN cable.LAN 1–4Connect personal computers, hubs or switches.3. LOCAL COMPUTER SETUPThe Wireless G B